Jump to content
Create New...

What Are Some of Your Neato Tools?


Recommended Posts

Been forever since I made a thread, so here's a fun one!

I love gadgets, especially useful ones.

First up, I have this GearWrench 1/4" drive Roto Ratchet

web.jpg

These things are super handy in tight spaces, plus I like how you can use them like a screwdriver once the bolt/nut is loosened up. Some people complain they are fragile (they are 72 tooth), but I think that has more to do with the tool being misused to try and break loose really stuck bolts/nuts. I've had this for several years and never had a problem.

Now for breaking stuck nuts and bolts loose, you need a proper tool, like one of these:

web.jpg

I have a GearWrench 24" Breaker Bar too, but this one is cool because it telescopes 18-24 inches. Really nicely made too. It's manufactured by Cal-Van.

Not really for automotive applications, but this is an extremely handy tool for removing and installing carburetor seats on small engines. It's made by Tecumseh.

web.jpg

It's always nice to be able to test your own battery, and while these things get quite hot, they are pretty useful at checking battery health by putting a load on them. The one I have is made by OTC.

web.jpg

Say you want to replace said battery, well you have to be careful if you have a security system on your car. Even if you don't its nice not to loose radio presets and be required to drive the car for the PCM to relearn everything. I had a simple memory keeper that plugged into the cigarette lighter and was powered by a 9V battery, but this one is more robust and has an indicator to confirm that it not only has power from the jump pack, but also that its connected to the vehicle successfully.

This is a Schumacher (OBD-L) OBDII Memory Saver Detector

web.gif

No auto tool collection is complete without a code scanner. Mine is a MATCO Tools Determinator MD 2007. It's pretty old, but it gets the job done and can stream live data. It has some OBDI connectors too,which is kinda cool, although not all the ones this pictured one has. It's got the nice case though.

web.jpg

Finally, the coolest tool I have is what you use when you want to do more than just load test a battery. What if you want to know its exact voltage and CCA rating? What if you want to test the starter and alternator? This handy tool can. It's a Midtronics MDX-650P Battery Conductance & Electrical System Analyzer.

web.jpg

I don't use it much, and as such it stays immaculate, but it's been super handy a few times. It can do Flooded/Lead Acid, AGM Flat Plate, AGM Spiral, Marine, Motorcycle, and Lawn/Garden batteries. It can test CA or CCA in or out of the vehicle. It's also got a printer built into it.

What are some of the interesting/nifty/specialty tools you guys have in your toy chests?

Link to comment
Share on other sites

I wrench on primarily vintage stuff, and that frequently requires a lot of torque. Busted the cylinder heads off my '64 last week; 3/4" bolt heads = solid 24" breaker bar and a foot-long pipe on that… but they all popped loose. I've broken bumper bracket bolts off with a similar arrangement, pushing with my leg and holding on to the car for anchorage.

 

- - - - -

I have this Germany-made item. Tho I've never had the occasion to use it, I did use a 3-ft wooden dowel the same way to detect an alternator's bearing was going bad :

 

DSC01206.jpg

 

DSC01207.jpg

 
I've seen slightly older versions with the Nazi Eagle stamped into the 'trumpet' end :
 
DSC01208.jpg
Link to comment
Share on other sites

Very cool, I have found the best tool is ones you have to modify yourself. Before Craftsman cam along with flexible wrenches, I would take my welding torch and heat up select wrenches and bend them so I had a 45 or 90 degree bend in them for reaching into tight places.

 

Now they seem to all make tools like this.

post-12-0-24749600-1440599217_thumb.jpg

 

I also love my 1970's craftmen tools as they truly were built tuff and solid.

Link to comment
Share on other sites

DSC03821_zpsfcaad9a2.jpg

^ 20+ inch Case steam engine wrench, 1918

 

DSC04308_zpsmcdt0jyb.jpg

^ General Hardware Mfg adjustable centerpunch

Pexto sheet metal hammer (my go-to), post 1947

no-name palette knife

Cresent 4" adjustable, 1930-1960

Spoon-ula

Craftsman center punch

Goodell-Pratt screwdriver

Stanley screwdriver

Twix angle gauge

Boston Wrench adjustable, patent date 1906

Vaughn & Bushnell pullers/nippers, post 1922

...Boston wrench aside, I use this crew regularly

 

DSC04310_zps5tza5fjb.jpg

^ Mmmmmm; knurling….

Edited by balthazar
Link to comment
Share on other sites

Join the conversation

You are posting as a guest. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



×
×
  • Create New...

Hey there, we noticed you're using an ad-blocker. We're a small site that is supported by ads or subscriptions. We rely on these to pay for server costs and vehicle reviews.  Please consider whitelisting us in your ad-blocker, or if you really like what you see, you can pick up one of our subscriptions for just $1.75 a month or $15 a year. It may not seem like a lot, but it goes a long way to help support real, honest content, that isn't generated by an AI bot.

See you out there.

Drew
Editor-in-Chief

Write what you are looking for and press enter or click the search icon to begin your search

Change privacy settings