Jump to content
Create New...
  • William Maley
    William Maley

    2018 Chevrolet Corvette To Sport A 6.2L DOHC V8

      A DOHC V8 is in the cards for the Corvette, but for which one?

    It seems dual overhead cams are making a return to the Corvette in one application. A set of GM service documents made their way on to Reddit sometime this morning. In the documents, there is a 6.2L DOHC V8 with LT5 code. Furthermore, the engine application corresponds to the 2018 Corvette. There isn't any indication of forced-induction being used for this engine.

    LT5 holds a special place in Corvette history. This was the code used for the only Corvette to ever feature a DOHC V8, the C4 ZR-1. 

    What could this engine be used for? The Drive believes this engine could be used for the mid-engine Corvette since it is a break from the traditional. We're wondering if there could be track-special Corvette that could use this engine.

    Source: The Drive, Reddit

    User Feedback

    Recommended Comments



    based off the noises my ..former.. 2.0t made at partial throttle there was definitely boost being made between 1800-2500rpm where I accelerated mostly. Obviously it was not max boost but I could hear it spooling through my intake. 

    Link to comment
    Share on other sites

    Drew based on your argument then a V8 would really seldom be needed as at lower speeds the same HP is needed to move a car along a 30 MPH. 

    My only point is that the ability of a new modern engine with force induction and VVT can give it the ability to make power on demand at lower RPM and over a wider RPM range. 

    With the older engines and single cam the ability to change the timing and take advantage of higher compression and other tuning is limited. 

    My point is if you can do all this on demand in a range of 1800-5300 RPM on 2 liters what can you do with 4.0 liters or even 6.2. 

    No I am not WOT leaving the light but If I choose I can make more torque or reach max torque at a lower speed and over a wider range. 

    And drop the N star as we may have thought it was cool when it came out but it really was a boat anchor. Also technology in the last 8 years has rendered it as modern as a Model A. 

    Link to comment
    Share on other sites

    My VW makes boost at partial throttle, given with the manual transmission i do have control over where i let the RPMs climb to.  An interesting note.  In my 2WD 4.7 HO/5 speed Dakota that is modified I have to shift out of 5th going over some of the mountains here while in 6th in the Beetle I do not have to downshift and even have some juice in reserve.  That seems to be a great effect of it having some boost built even though I am only at enough throttle to hold a steady speed.  Also, FI vehicles are also less effected by elevation.  That said I am still a huge fans of NA engines and thinks certain cars would stick with these (Vette being one) instead of smaller turbo motors.  Sometimes it is all about the character of the vehicle he engine is in. 

    • Agree 1
    Link to comment
    Share on other sites

    The only reason I'm using the N* as an example was because of its similar peak horsepower and torque to the 2.0t. My modern comparison choice is the 6.2 V8 verse the 3.6tt, but far fewer people have experience driving either or both of those.

     

    Link to comment
    Share on other sites

    52 minutes ago, Drew Dowdell said:

    The only reason I'm using the N* as an example was because of its similar peak horsepower and torque to the 2.0t. My modern comparison choice is the 6.2 V8 verse the 3.6tt, but far fewer people have experience driving either or both of those.

     

    Peak figures may be close. But the torque below peak in the 2.0T is superior to that Northstar, throttle opening vs throttle opening. 

    Link to comment
    Share on other sites

    6 hours ago, Drew Dowdell said:

    The only reason I'm using the N* as an example was because of its similar peak horsepower and torque to the 2.0t. My modern comparison choice is the 6.2 V8 verse the 3.6tt, but far fewer people have experience driving either or both of those.

     

    Drew it is as simple as this. I can hit peak HP at a lower RPM and at will in a wider range than a single cam engine without VVT.  In fact I can hit higher numbers than some with 4 more cylinders.

    Apply this technology from the 4 cylinder delivering this kind of performance profile to 4 more cylinders putting out 150 per liter and it can tell you how far you can push the HP up and how drive able the car is. 

    Trust me no one will be disappointed in the feel as you call it. Even in a NA version for a base car it could do many things and even spread the power band out along with a 10 speed tranny that will keep it in the sweetest spot regardless of the speed. 

    We have many tools today to let cars do things no though possible many years ago. My little wizz bang engine puts out numbers a GN never saw and much less survived less modifications. Apply this to other engines and you will find much more tuning available and yes GM will use it. 

    My take is the 6.2 is a NA engine and will put out a lot of power with a wide torque band. Cadillac will do much the same at 4.0 and TT. 

    Either way the push rod is nearing the end I am sad to say, It has gone farther than anyone has ever considered but the EPA regs are going to kill it. Also global displacment taxes in this global auto market is in play hence the TT 4.0 Cadillac vs the NA 6.2 Chevy. 

     

    Link to comment
    Share on other sites

    This isn't pushrod v. DOHC.... this is Displacement v. Turbo. 

    The 6.2 Pushrod is roughly equal to the most advanced 3.6TT today. Now add DOHC to it.... it's going to blow the 3.6TT out of the water.   Of course a 6.2TT will be awesome, I'm not denying that... there is no 12 cylinder 12 liter N/A engine out there that would be the power equivalent to such a beast. 

    I'm saying that in the case of the family car... a 2.0T is not all it is cracked up to be as a V6 replacement.  There is less power and no gain in fuel economy.  

    Link to comment
    Share on other sites

    7 minutes ago, ccap41 said:

    There is more torque by a mile though. And in the usable rpm range as well.

    That... would be incorrect.  There may be more torque at points, but certainly not by a mile and certainly not overall either.  This is ATS 2.0T v. ATS 3.6 V6 . In the Turbo, see that steep cliff up front? The V6 is almost never under 200 lb-ft of torque.  However, again, these are full throttle dyno pulls.  Take away most of the boost and the curve for the turbo will be very different..... just because you're at 1700rpm on either engine, does not mean you're getting 260 lb-ft... but on the turbo that will be especially true since boost will be lower.  As boost drops, so does torque.   On an engine that does not rely on boost for its torque, the effect on torque at part throttle will be lesser.  It is worth point out that in spite of the similar outputs of these two engines, the V6 is about .75 seconds faster to 60. 

    engine_LTG_ATS.jpg

    2016_LGX_36LV6VVT_ATS_061715.jpg

     

    I really wish we could get a part throttle dyno pull on these two for comparison. 

    Link to comment
    Share on other sites

    1 hour ago, Drew Dowdell said:

    This isn't pushrod v. DOHC.... this is Displacement v. Turbo. 

    The 6.2 Pushrod is roughly equal to the most advanced 3.6TT today. Now add DOHC to it.... it's going to blow the 3.6TT out of the water.   Of course a 6.2TT will be awesome, I'm not denying that... there is no 12 cylinder 12 liter N/A engine out there that would be the power equivalent to such a beast. 

    I'm saying that in the case of the family car... a 2.0T is not all it is cracked up to be as a V6 replacement.  There is less power and no gain in fuel economy.  

    " The 6.2 Pushrod is roughly equal to the most advanced 3.6TT today. Now add DOHC to it.... it's going to blow the 3.6TT out of the water "

    I'm sure you have proof, right? 

    As it stands right now, the Raptor 3.5TT tune HP is equivalent to a 6.2 OHV, yet it's torque is superior ( peak and RPM range )...

    Then there is the Ford GT 3.5TT...

    And your 6.2 DOHC " blow out of the water " is pure speculation at this point. ( see the MB M 156 and M159 engines for a measuring stick ).

    Link to comment
    Share on other sites

    Just now, FordCosworth said:

    " The 6.2 Pushrod is roughly equal to the most advanced 3.6TT today. Now add DOHC to it.... it's going to blow the 3.6TT out of the water "

    I'm sure you have proof, right? 

    As it stands right now, the Raptor 3.5TT tune HP is equivalent to a 6.2 OHV, yet it's torque is superior ( peak and RPM range )...

    Then there is the Ford GT 3.5TT...

    And your 6.2 DOHC " blow out of the water " is pure speculation at this point. ( see the MB M 156 and M159 engines for a measuring stick ).

    I'm doing a comparison inside specific companies.  I was sticking with GM for the moment because of the similarity of the output of their 3.6TT and the 6.2 liter.   The 6.2 is a pushrod and it already matches the output of the 3.6TT.... so yes, I can be fairly confident that a 6.2 liter DOHC will out perform a 6.2 liter pushrod otherwise there would be little point for GM to do it, thus blowing the GM 3.6TT out of the water. 

    Link to comment
    Share on other sites

    25 minutes ago, FordCosworth said:

    " The 6.2 Pushrod is roughly equal to the most advanced 3.6TT today. Now add DOHC to it.... it's going to blow the 3.6TT out of the water "

    I'm sure you have proof, right? 

    As it stands right now, the Raptor 3.5TT tune HP is equivalent to a 6.2 OHV, yet it's torque is superior ( peak and RPM range )...

    Then there is the Ford GT 3.5TT...

    And your 6.2 DOHC " blow out of the water " is pure speculation at this point. ( see the MB M 156 and M159 engines for a measuring stick ).

    But... if you insist... I can pick on Ford.

    The brand new 2.0T offers a lot less horsepower in standard tune in the Fusion than the 10 year old 3.7 did in the Mazda 6.  The 3.5 V6 in the Edge is a big step up from the 2.0T.

    Sure, there is still the 2.3... but then you've just added displacement, which is the bulk of my argument that there is no replacement for.... also, my multiple experiences in the 2.3 powered mustang convertible have shown very poor fuel economy for a 4-cylinder. 

    Link to comment
    Share on other sites

    52 minutes ago, Drew Dowdell said:

    But... if you insist... I can pick on Ford.

    The brand new 2.0T offers a lot less horsepower in standard tune in the Fusion than the 10 year old 3.7 did in the Mazda 6.  The 3.5 V6 in the Edge is a big step up from the 2.0T.

    Sure, there is still the 2.3... but then you've just added displacement, which is the bulk of my argument that there is no replacement for.... also, my multiple experiences in the 2.3 powered mustang convertible have shown very poor fuel economy for a 4-cylinder. 

     

    I didn't insist anything. I showed some fallacies in your comment.

    You said " brand/mfg specific ", therefore I left as is.

    If you like,  I can play your petty little game Drew...

    Edited by Drew Dowdell
    fixed broken quotes
    Link to comment
    Share on other sites

    My argument is that there is no replacement for displacement in cars that are driven normally... and you cite the Raptor and GT as counter examples..... the reason you resort to those is that you can't refute my argument using normal vehicles...... logical fallacy indeed.

    I'm specifically limiting this to vehicles that can conceivably be considered average family vehicles... not specialty Hi-Po trucks and supercars limited to runs of under 1000 units. I'm looking for satisfaction in driving for a normal driver... we are repeatedly told that Turbo-4s offer better fuel economy and power to a V6.... that is largely proving to not be true in normal driving

    It's a simple comparison.... Taurus 2.0T or 3.5 V6.  Explorer 2.3T or 3.5 V6.  ATS 2.0T or ATS V6. CTS 2.0T or CTS V6.  I know which of each I would choose... and why. 

    Link to comment
    Share on other sites

    And the reason I'm limiting it to these vehicles is because over the most recent year or three that I've been testing these vehicles, I've been finding the Turbo-4s to be largely underwhelming compared to a V6 counterpart.  The driving satisfaction just isn't equal.  V6es pull better and usually get about equal highway MPGs. So why are we being forced into these underwhelming products by manufacturers and being fed lies to do it?

    Link to comment
    Share on other sites

    29 minutes ago, FordCosworth said:

     

    I didn't insist anything. I showed some fallacies in your comment.

    You said " brand/mfg specific ", therefore I left as is.

    If you like,  I can play your petty little game Drew...

    Actually he was comparing one GM motor to another GM motor and you took it upon yourself to interject Ford motors into this when it wasn't a part of his initial comparison. 

    • Disagree 1
    Link to comment
    Share on other sites

    7 minutes ago, Drew Dowdell said:

    My argument is that there is no replacement for displacement in cars that are driven normally... and you cite the Raptor and GT as counter examples..... the reason you resort to those is that you can't refute my argument using normal vehicles...... logical fallacy indeed.

    I'm s... not specialty Hi-Po trucks and supercars limited to runs of under 1000 units. I'm looking for satisfaction in driving for a normal driver... we are repeatedly told that Turbo-4s offer better fuel economy and power to a V6.... that is largely proving to not be true in normal driving

    It's a simple comparison.... Taurus 2.0T or 3.5 V6.  Explorer 2.3T or 3.5 V6.  ATS 2.0T or ATS V6. CTS 2.0T or CTS V6.  I know which of each I would choose... and why. 

    your words...

    " roughly equal to the most advanced 3.6TT today "

    I cited 2 examples of TT V-6's that are more than what GM has..ouch...

    Now you're saying something about " specifically limiting this to vehicles that can conceivably be considered average family vehicle " in a thread about a 6.2L DOHC that will definitely not be in ANY family sedan, but will likely be in a Mid Engine Supercar?

     

     

     

    Link to comment
    Share on other sites

    6 minutes ago, FordCosworth said:

    your words...

    " roughly equal to the most advanced 3.6TT today "

    I cited 2 examples of TT V-6's that are more than what GM has..ouch...

    Now you're saying something about " specifically limiting this to vehicles that can conceivably be considered average family vehicle " in a thread about a 6.2L DOHC that will definitely not be in ANY family sedan, but will likely be in a Mid Engine Supercar?

     

     

     

    Maybe you missed the part where he stated "3.6" in that TT remark. Last time I checked, Ford did not make a 3.6L TT, hence him (again) referring to only a GM motor. 

    Link to comment
    Share on other sites

    9 minutes ago, FordCosworth said:

    your words...

    " roughly equal to the most advanced 3.6TT today "

    I cited 2 examples of TT V-6's that are more than what GM has..ouch...

    Now you're saying something about " specifically limiting this to vehicles that can conceivably be considered average family vehicle " in a thread about a 6.2L DOHC that will definitely not be in ANY family sedan, but will likely be in a Mid Engine Supercar?

     

     

     

    Really? Neither of the Fords have cylinder deactivation nor auto stop.  GM has the only Turbo-6s with both of those technologies. Getting raw power is just dialing up the boost, using better metal, and using stronger bolts. Ouch is right. 

    You must have missed the 95% of this thread where I was comparing the GM 2.0T to the Cadillac Northstar.  In nearly every post, I've had to make the statement "in normal driving".   I'm largely unconcerned about the 6.2 DOHC because it's not going into a "normal" vehicle unless it ends up in the Escalade or CT6 also... even then, those are a lot less normal than what I'm talking about here.  The only reason I bring up the 6.2 DOHC is because it is certainly going to out-perform the 6.2 pushrod and the 6.2 pushrod equals the performance of the 3.6TT. 

     

    Still... Edge 2.0t or Edge 3.5 V6. just off the lot... no mods.... Which one will provide greater driving satisfaction for you?

     

    Link to comment
    Share on other sites

    4 minutes ago, Drew Dowdell said:

    Really? Neither of the Fords have cylinder deactivation nor auto stop.  GM has the only Turbo-6s with both of those technologies. Getting raw power is just dialing up the boost, using better metal, and using stronger bolts. Ouch is right. 

    You must have missed the 95% of this thread where I was comparing the GM 2.0T to the Cadillac Northstar.  In nearly every post, I've had to make the statement "in normal driving".   I'm largely unconcerned about the 6.2 DOHC because it's not going into a "normal" vehicle unless it ends up in the Escalade or CT6 also... even then, those are a lot less normal than what I'm talking about here.  The only reason I bring up the 6.2 DOHC is because it is certainly going to out-perform the 6.2 pushrod and the 6.2 pushrod equals the performance of the 3.6TT. 

     

    Still... Edge 2.0t or Edge 3.5 V6. just off the lot... no mods.... Which one will provide greater driving satisfaction for you?

     

    Raptor has auto stop/start. The GT may or may not. Gen 2 EB 3.5TT is both DI and Port Injection. Ford has the only Turbo-6s with both of those technologies...ouch is right.

    Of the two, I prefer the Edge 2.0T. And that was the less advanced 2015's. Still looking to test 2017's and specifically the 2.7TT Sport. 

     

     

     

     

     

    Link to comment
    Share on other sites

    29 minutes ago, Drew Dowdell said:

    My argument is that there is no replacement for displacement in cars that are driven normally... and you cite the Raptor and GT as counter examples..... the reason you resort to those is that you can't refute my argument using normal vehicles...... logical fallacy indeed.

    I'm specifically limiting this to vehicles that can conceivably be considered average family vehicles... not specialty Hi-Po trucks and supercars limited to runs of under 1000 units. I'm looking for satisfaction in driving for a normal driver... we are repeatedly told that Turbo-4s offer better fuel economy and power to a V6.... that is largely proving to not be true in normal driving

    It's a simple comparison.... Taurus 2.0T or 3.5 V6.  Explorer 2.3T or 3.5 V6.  ATS 2.0T or ATS V6. CTS 2.0T or CTS V6.  I know which of each I would choose... and why. 

    I know I'm comparing 2 generations but fairly comparable.. 3.0V6 in the last gen Escape and the 2.0T in the current Escape.

    Both 240hp.

    V6 Tq: 223lb-ft

    1500lbs towing

    19/25 mpg(FWD)

    2.0T Tq: 270 lb-ft

    3500lbs towing

    22/30mpg(FWD)

    The Explorer is the only one of those I would take the N/A V6 over the turbo mill. N/A V6's...blow. Maybe the Taurus as well.. but I just hate the Taurus so much I would never even consider this old as F one that is out now. My argument would be there CAN be replacement for displacement and it varies a lot on the application and intent.

    • Agree 1
    Link to comment
    Share on other sites

    Just now, ccap41 said:

    I know I'm comparing 2 generations but fairly comparable.. 3.0V6 in the last gen Escape and the 2.0T in the current Escape.

    Both 240hp.

    V6 Tq: 223lb-ft

    1500lbs towing

    19/25 mpg(FWD)

    2.0T Tq: 270 lb-ft

    3500lbs towing

    22/30mpg(FWD)

    The Explorer is the only one of those I would take the N/A V6 over the turbo mill. N/A V6's...blow. Maybe the Taurus as well.. but I just hate the Taurus so much I would never even consider this old as F one that is out now. My argument would be there CAN be replacement for displacement and it varies a lot on the application and intent.

    I'm not denying that the 2.0T is an improvement over the old old Vulcan 3.0.... but the old 3.0 is not an example of today's technology... even the 3.5 and 3.5 are not that current.  A modern 2.0T v. a Modern V6 around 3.5-3.7 liters?  I'll take the V6 thanks. 

    I continuously get equal or better fuel economy out of the V6es than I do out of the 4-cylinder Turbos that are supposed to replace them... and I get better power delivery as well. 

    6 minutes ago, FordCosworth said:

    Really? 

    So did the 1917 Liberty V-12. And before that, Renault has varying success with Turbos

    I never said Olds was the first. Nor the Avalon (though I think it might have been). Nor the Cadillac.

     

    However, port and direct injection in the same engine is not some gigantic technological leap forward. It is using an older technology to enhance fuel economy and low speed engine operation.  It's the tech equivalent of a direct drive water pump.

    Getting Turbo to work right along side of cylinder deactivation is challenging... and then there is the auto stop to consider. 

    Link to comment
    Share on other sites

    5 minutes ago, Drew Dowdell said:

    I'm not denying that the 2.0T is an improvement over the old old Vulcan 3.0.... but the old 3.0 is not an example of today's technology

    I can understand this point.

     

    5 minutes ago, Drew Dowdell said:

     A modern 2.0T v. a Modern V6 around 3.5-3.7 liters?

    Yeah... I'm just not a huge fan of V6's in general. I'd rather the 4cyl turbo in most applications.

    Link to comment
    Share on other sites

    I get what Drew is saying.. in current technological terms I really didn't see much of a difference in the power output from the LT1 versus the LF4.  Performance-wise the ATS-V is 464HP and 445lb while the Camaro is 455/455. In tests that I've seen the ATS 0-60 is 3.8 sec and the SS 4.0 to 60. Even if one discounts this either direction.. they are extremely similar, almost interchangeable. The need for the smaller displacement in the Caddy was because of international markets. 

    Link to comment
    Share on other sites

    54 minutes ago, Cmicasa the Great said:

    I get what Drew is saying.. in current technological terms I really didn't see much of a difference in the power output from the LT1 versus the LF4.  Performance-wise the ATS-V is 464HP and 445lb while the Camaro is 455/455. In tests that I've seen the ATS 0-60 is 3.8 sec and the SS 4.0 to 60. Even if one discounts this either direction.. they are extremely similar, almost interchangeable. The need for the smaller displacement in the Caddy was because of international markets. 

    What're the mileage rating differences? 

    Link to comment
    Share on other sites

    Wow this argument really has degraded.

    the fact is this engine is coming as there is no avoiding it. The Corvette team has never come with a new model with anything less than what we already had since 1984.

    We also have seen the results of not continuing to advance a product in the global market in the Viper. 

    GM is one of the few who could pull this off. 

    I have read many post on the web and it is even worse with some other in the cheese and whine crowd. They are telling tales of $500 oil changes and complaining they just now could afford to buy a DOHC ZR1? If that was the case they could not have bought a ne Vette since the 80's.

    One said that it was impossible to make a low cost mid engine sports car. I guess he forgot they sold nearly 400k of them even saddled with a poorly managed and funded program.

    People need to get over their hurt feelings and let this unfold as it is properly funded and in good hands that will make sure the car and its legacy is protected for this model and future models. 

    As it is they have taken the engine and layout as far as they can with pending and future issues. Even the hybrid assist is on the table as it may be the only way they keep a V8 in the car.

    It is time to trust Tadge and crew as they to this point have only given us the best Corvettes ever and do not take lightly the need to protect the car and keep it relevant in a global market.

    They could just as easy just keep making the same thing and retire when the car finally dies.

    Edited by hyperv6
    • Agree 1
    Link to comment
    Share on other sites

    I absolutely support the 6.2 DOHC.... the more options the better.   I'm only hoping that it also goes into something in the Cadillac lineup too... maybe a 2-seater sports car or some variants of the CT6 line... or even just the Escalade would be nice. 

    Link to comment
    Share on other sites

    1 hour ago, Drew Dowdell said:

    I absolutely support the 6.2 DOHC.... the more options the better.   I'm only hoping that it also goes into something in the Cadillac lineup too... maybe a 2-seater sports car or some variants of the CT6 line... or even just the Escalade would be nice. 

    You just need to let this play out as there are many options here.

    We now know Chevy has the 6.2 coming and we know Cadillac has a TT 4.0 in the works. 

    Now how will they do this? Well it could be several ways.

    They could do a similar block and share but make each version distinct to each division.

    The Chevy coul be based on ther already available DOHC set up from Mercury Marine made for the GM engine. The did the Mercury deal once before and the engine they have now is not even near what it could do.

    Odds are a better funded GM will do this in house and two different engines fir each division.

    No matter what has any new Corvette platform dropped the ball since 1984? No and that is why the C8 will move the heritage forward as the others.

    People bitched when the pop up head lamps went away, yet no one complains today and we have better lights. They complained the tail lights were not as round as they used to be yet today no one complains. Change the engine and move it they will complain till the lap times and reviews come in.

    • Agree 1
    Link to comment
    Share on other sites

    13 hours ago, Cmicasa the Great said:

    Camaro 17/28 and  ATS-V 17/24.. again the ATS probably has more drag due to styling and the Camaro is about 100lbs lighter

    Interesting.. 4mpg highway is a big difference. I'd also assume the ATS-V is geared differently, more aggressively.

    Link to comment
    Share on other sites

    10 minutes ago, Cmicasa the Great said:

    Perhaps... But I still have more faith in the weight and drag argument.  

    100lbs is negligible at highway cruising but I would agree with increased drag.

    Link to comment
    Share on other sites

    The ATS-V does better than the EPA rating on the highway... There would need to be a significant difference in aero for that amount of fuel economy difference and I just don't see it. For reference, a 707hp Charger Hellcat, also with an 8speed auto, all of the aerodynamics of a brick, and a lot more weight gets just 2mpg less on the highway. 

    My guess is that you're just into the boost more on the ATS.

    Link to comment
    Share on other sites

    7 minutes ago, smk4565 said:

    If they are making a 6.2 liter engine for a mid engine car, why on earth doesn't it have 12 cylinders?  

    Here's the bigger question you should be asking. Why on earth does it need 12 cylinders?

    • Agree 3
    Link to comment
    Share on other sites

    19 minutes ago, Cmicasa the Great said:

    Its his way of putting GM down... That is the way of his world

    Oh I know and it was meant as a rhetorical statement because there is absolutely no need for a 12 cylinder at all. That's just for people who want to wave their money dicks around with nothing to really show for it. 

    • Agree 1
    Link to comment
    Share on other sites

    1 hour ago, smk4565 said:

    If they are making a 6.2 liter engine for a mid engine car, why on earth doesn't it have 12 cylinders?  

    Because that's completely unnecessary ..and CAFE.. Unlike those Euro companies GM sells Vettes in very good numbers.

    57 minutes ago, surreal1272 said:

    Oh I know and it was meant as a rhetorical statement because there is absolutely no need for a 12 cylinder at all. That's just for people who want to wave their money dicks around with nothing to really show for it. 

    Especially when all of the recently tested AMG 65's are slower than the AMG 63's because too much power.

    Worthless without traction.

    Edited by ccap41
    • Agree 1
    Link to comment
    Share on other sites

    What's funny is his beloved Mercedes barely even competes in the performance spectrum against GM's V Series or Z06.

    ATS-V beats the C63 S and M3 in the 1/4 mile and to 150mph

    ATS-V: 19.8sec to 150mph

    C63 S: 23.7sec to 150mph 

    M3: 23.3sec to 150mph

    Comparo

    Need another comparo?

    'Nother Comparo

    Still quickest, brakes the best, and "dusted" the M3 and C63 in their skidpad as well.

    • Agree 1
    Link to comment
    Share on other sites

    6 hours ago, ccap41 said:

    What's funny is his beloved Mercedes barely even competes in the performance spectrum against GM's V Series or Z06.

    ATS-V beats the C63 S and M3 in the 1/4 mile and to 150mph

    ATS-V: 19.8sec to 150mph

    C63 S: 23.7sec to 150mph 

    M3: 23.3sec to 150mph

    Comparo

    Need another comparo?

    'Nother Comparo

    Still quickest, brakes the best, and "dusted" the M3 and C63 in their skidpad as well.

    Whoooooah whoooooooah Whoooooah.. but the C63 has. supposedly, a better User Interface and entertainment system..:rolleyes: of course my motto remains... FUCK Mercedes

    • Agree 1
    Link to comment
    Share on other sites

    17 minutes ago, Cmicasa the Great said:

    Whoooooah whoooooooah Whoooooah.. but the C63 has. supposedly, a better User Interface and entertainment system..:rolleyes: of course my motto remains... f@#k Mercedes

    But but but.. Cadillac doesn't have a V12! 

    Link to comment
    Share on other sites

    8 hours ago, surreal1272 said:

    Here's the bigger question you should be asking. Why on earth does it need 12 cylinders?

    Because 12 cylinders is better than 8.  The Lambos and Ferraris have them.

    Link to comment
    Share on other sites




    Join the conversation

    You can post now and register later. If you have an account, sign in now to post with your account.
    Note: Your post will require moderator approval before it will be visible.

    Guest
    Add a comment...

    ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.


  • google-news-icon.png



×
×
  • Create New...

Hey there, we noticed you're using an ad-blocker. We're a small site that is supported by ads or subscriptions. We rely on these to pay for server costs and vehicle reviews.  Please consider whitelisting us in your ad-blocker, or if you really like what you see, you can pick up one of our subscriptions for just $1.75 a month or $15 a year. It may not seem like a lot, but it goes a long way to help support real, honest content, that isn't generated by an AI bot.

See you out there.

Drew
Editor-in-Chief

Write what you are looking for and press enter or click the search icon to begin your search

Change privacy settings