• Sign in to follow this  
    Followers 0

    General Motors Officially Releases Details On 6.6L Duramax Diesel V8


    • Those leaked numbers from the weekend? They check out.


    Over the weekend, General Motors published and then deleted the power figures for the new 6.6L Duramax Diesel V8 that would be appearing in the 2017 Chevrolet Silverado HD and GMC Sierra HD. Today at the Texas State Fair, GM revealed everything about this new engine.

    We'll begin with the most important detail, power output. The numbers that GM revealed match the numbers posted to their powertrain site - 445 horsepower and 910 pound-feet of torque. Compared to the current Duramax V8, the new engine produces 48 more horsepower and 145 more pound-feet of torque.

    How was GM able to pull this off? They basically went through the engine with a fine tooth comb and made various changes. GM says 90 percent of this engine has been changed. Some of the changes include new electronically controlled, variable-vane turbocharger, revised cylinder heads, improved cooling, and revised fuel delivery system. The updated Duramax can also run B20 bio-diesel.

    Figures for payload and towing will be announced at a later date.

    Source: Chevrolet, GMC
    Press Release is on Page 2


    DALLAS — Chevrolet today announced the redesigned Duramax 6.6L V-8 turbo-diesel offered on the 2017 Silverado HD. This next-generation redesign offers more horsepower and torque than ever — an SAE-certified 445 horsepower (332 kW) and 910 lb.-ft. (1,234 Nm) — to enable easier, more confident hauling and trailering.

    Along with a 19 percent increase in max torque over the current Duramax 6.6L, the redesigned turbo-diesel’s performance is quieter and smoother, for greater refinement. In fact, engine noise at idle is reduced 38 percent.

    “With nearly 2 million sold over the past 15 years, customers have forged a bond with the Duramax diesel based on trust and capability,” said Dan Nicholson, vice president, Global Propulsion Systems. “The new Duramax takes those traits to higher levels.”

    The new Duramax 6.6L shares essentially only the bore and stroke dimensions of the current engine and incorporates a new, GM-developed control system. The Duramax’s signature low-rpm torque production hasn’t changed and still offers 90 percent of peak torque at a low 1,550 rpm and sustains it through 2,850 rpm.

    “Nearly everything about the Duramax is new, designed to produce more torque at lower rpm and more confidence when trailering or hauling,” said Gary Arvan, chief engineer. “You’ll also notice the refinement improvements the moment you start the engine, and appreciate them as you cruise quietly down the highway — with or without a trailer.”

    Additional highlights include:

    • New, stronger cylinder block and cylinder heads
    • New, stronger rotating and reciprocating assembly
    • Increased oil- and coolant-flow capacity
    • New EGR system with single cooler and integrated bypass
    • New electrically actuated/electronically controlled turbocharging system
    • All-new advanced solenoid fuel system
    • All-new electronic controls
    • New full-length damped steel oil pan that contributes to quietness
    • New rocker cover/fuel system acoustical treatments
    • B20 bio-diesel compatibility
    • SAE-certified 445 net horsepower (332 kW) at 2,800 rpm
    • SAE-certified 910 net lb.-ft. of torque (1,234 Nm) at 1,600 rpm

    A new, patent-pending vehicle air intake system — distinguished on the Silverado HD by a bold hood scoop — drives cool, dry air into the engine for sustained performance and cooler engine temperatures during difficult conditions, such as trailering on steep grades. Cooler air helps the engine run better under load, especially in conditions where engine and transmission temperatures can rise quickly. That allows the Duramax to maintain more power and vehicle speed when trailering in the toughest conditions.

    The intake design is another example of the advanced integration included in the 2017 Silverado HD that makes it over-the-road capable.   

    A strong foundation
    As with previous versions, the new Duramax block features a strong cast-iron foundation known for its durability, with induction-hardened cylinder walls and five nodular iron main bearings. It retains the same 4.05-inch (103mm) and 3.89-inch (99mm) bore and stroke dimensions as the current engine, retaining the Duramax’s familiar 6.6L (403 cu.-in./6,599 cc) displacement.

    A deep-skirt design and four-bolt, cross-bolted main caps help ensure the block’s strength and enable more accurate location of the rotating assembly. A die-cast aluminum lower crankcase also strengthens the engine block and serves as the lower engine cover, while reducing its overall weight.

    The new engine block incorporates larger-diameter crankshaft connecting rod journals than the current engine, enabling the placement of a stronger crankshaft and increased bearing area to handle higher cylinder loads.

    An enhanced oiling circuit, with higher flow capacity and a dedicated feed for the turbocharger, provides increased pressure at the turbo and faster oil delivery. Larger piston-cooling oil jets at the bottom of the cylinder bores spray up to twice the amount of engine oil into oil galleries under the crown of the pistons, contributing to lower engine temperature and greater durability.

    A new, two-piece oil pan contributes to the new Duramax’s quieter operation. It consists of a laminated steel oil pan with an upper aluminum section. The aluminum section provides strength-enhancing rigidity for the engine, but a pan made entirely of aluminum would radiate more noise, so the laminated steel lower section is added to dampen noise and vibration.

    There’s also an integrated oil cooler with 50 percent greater capacity than the current engine’s, ensuring more consistent temperatures at higher engine loads.

    Segment firsts

    • Re-melt piston bowl rim
    • Venturi Jet Drain Oil Separator
    • Closed-loop glow plug temperature control

    Stronger pistons with remelt
    A tough, forged micro-alloy steel crankshaft anchors the new Duramax’s stronger rotating assembly. Cut-then-rolled journal fillets contribute to its durability by strengthening the junction where the journals — the round sections on which the bearings slide — meet the webs that separate the main and rod journals.

    The connecting rods are stronger, too, and incorporate a new 45-degree split-angle design to allow the larger-diameter rod bearings to pass through the cylinder bores during engine assembly. They’re forged and sintered with a durable powdered metal alloy, with a fractured-cap design enabling more precise cap-to-rod fitment. 

    A new, stronger cast-aluminum piston design tops off the rotating assembly. It features a taller crown area and a remelted combustion bowl rim for greater strength. Remelting is an additional manufacturing process for aluminum pistons in which the bowl rim area is reheated after casting and pre-machining, creating a much finer and more consistent metal grain structure that greatly enhances thermal fatigue properties.

    Additionally, the Duramax’s pistons don’t use pin bushings, reducing reciprocating weight to help the engine rev quicker and respond faster to throttle changes.

    Lightweight cylinder heads, solenoid injectors
    The redesigned engine retains the Duramax’s signature first-in-class aluminum cylinder head design, with six head bolts per cylinder and four valves per cylinder. The aluminum construction helps reduce the engine’s overall weight, while the six-bolt design provides exceptional head-clamping strength — a must in a high-compression, turbocharged application.

    A new aluminum head casting uses a new double-layer water core design that separates and arranges water cores in layers to create a stiffer head structure with more precise coolant flow control. The heads’ airflow passages are also heavily revised to enhance airflow, contributing to the engine’s increased horsepower and torque.

    The Duramax employs a common-rail direct injection fuel system with new high-capability solenoid-type injectors. High fuel pressure of 29,000 psi (2,000 bar) promotes excellent fuel atomization for a cleaner burn that promotes reduced particulate emissions. The new injectors also support up to seven fuel delivery events per combustion event, contributing to lower noise, greater efficiency and lower emissions. Technology advancements enable less-complex solenoid injectors to deliver comparable performance to piezo-type injectors.

    Electronically controlled, variable-geometry turbocharging system
    A new electronically controlled, variable-vane turbocharger advances the Duramax’s legacy of variable-geometry boosting. Compared to the current engine, the system produces higher maximum boost pressure — 28 psi (195 kPa) — to help the engine make more power, and revisions to enhance the capability of the exhaust-brake system.

    Along with a new camshaft profile and improved cylinder head design, the Duramax’s new variable-vane turbocharger enables the engine to deliver more power with lower exhaust emissions. It uses a more advanced variable-vane mechanism, allowing a 104-degree F (40 C) increase in exhaust temperature capability. The self-contained mechanism decouples movement from the turbine housing, allowing operation at higher temperature. That enables the engine to achieve higher power at lower cylinder pressure. Additionally, it has lower internal leakage, allowing more exhaust energy to be captured during exhaust braking.

    The integrated exhaust brake system makes towing less stressful by creating added backpressure in the exhaust, resulting in negative torque during deceleration and downhill driving, enhancing driver control and prolonging brake pad life.

    Venturi Jet Drain Oil Separator
    A new Venturi Jet Drain Oil Separator employed with the Duramax 6.6L is the first of its type in the segment and is designed to ensure oil control in sustained full-load operation. The totally sealed system collects the fine mist of oil entrained in the blow-by gas and uses a small portion of the boosted air generated by the turbocharger to pump the collected oil back to the engine oil sump for re-use by the engine. Less sophisticated systems are not able to return this oil during full-load operation, which can result in oil carryover into the cylinders during combustion.

    Cold Start System
    The new Duramax also provides outstanding cold-weather performance, with microprocessor-controlled glow plugs capable of gas-engine-like starting performance in fewer than 3 seconds in temperatures as low as -20 degrees F (-29 C) without a block heater. The system is enhanced with ceramic glow plugs and automatic temperature compensation — a first-in-class feature providing improved robustness and capability. The automatic temperature compensation assesses and adjusts the current to each glow plug for every use, providing optimal temperature for cold start performance and durability.     

    Electronic throttle valve and cooled EGR
    Unlike a gasoline engine, a diesel engine doesn’t necessarily require a throttle control system. The Duramax 6.6L employs an electronic throttle valve to regulate intake manifold pressure in order to increase exhaust gas recirculation (EGR) rates. It also contributes to smoother engine shutdown.

    Additionally, a cooled exhaust gas recirculation (EGR) system enhances performance and helps reduce emissions by diverting some of the engine-out exhaust gas and mixing it back into the fresh intake air stream, which is fed through the cylinder head for combustion. This lowers combustion temperatures, improving emissions performance by reducing NOx formation.

    The exhaust is cooled in a unique heat exchanger before it’s fed into the intake stream through a patented EGR mixing device, further improving emissions and performance capability. An integrated bypass allows non-cooled exhaust gas to be fed back into the system to help the engine more quickly achieve optimal operating temperature when cold.

    B20 Biodiesel Capability
    The new Duramax 6.6L is capable of running on B20 biodiesel, a fuel composed of 20 percent biodiesel and 80 percent conventional diesel. B20 helps lower carbon dioxide emissions and lessens dependence on petroleum. It is a domestically produced, renewable fuel made primarily of plant matter — mostly soybean oil.

    Manufacturing
    The new Duramax 6.6L turbo-diesel engine is produced with locally and globally sourced parts at the DMAX Ltd. (GM’s joint venture with Isuzu) manufacturing facility in Moraine, Ohio.

    Allison 1000 Automatic Transmission
    The proven Allison 1000 six-speed automatic transmission is matched with the new Duramax 6.6L. A number of refinements have been made to accommodate the engine’s higher torque capacity, including a new torque converter.

    The Allison 1000’s technologically advanced control features, such as driver shift control with manual shift feature and a patented elevated idle mode cab warm-up feature, haven’t changed. Also, the Tow/Haul mode reduces shift cycling for better control and improved cooling when towing or hauling heavy loads.

    There’s also a smart diesel exhaust brake feature that enhances control when descending steep grades.

    0


    Sign in to follow this  
    Followers 0


    User Feedback


    That is a big change in parts.....

     

    These engines are pretty solid anyways, but I can't help but wonder if there will be issues..

     

     

    90 percent new is a lot....

    0

    Share this comment


    Link to comment
    Share on other sites


    Your content will need to be approved by a moderator

    Guest
    You are commenting as a guest. If you have an account, please sign in.
    Add a comment...

    ×   You have pasted content with formatting.   Remove formatting

      Only 75 emoticons maximum are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor




  • Popular Stories

  • Today's Birthdays

    1. Bandit '79
      Bandit '79
      (44 years old)
    2. Ur_pimp
      Ur_pimp
      (27 years old)
  • Similar Content

    • By William Maley
      If it weren't for focus groups, the design of the 2018 Chevrolet Equinox could have looked so much different.
      Speaking to Automotive News, chief engineer of the 2018 Equinox Mark Cieslak revealed that focus groups weren't not impressed with the first designs of the redesigned model. They described the design as being bulky, 'not compelling', and looking a bit odd. If this was old GM, they would have gone forward with the design.
      "Back in the day, we would have probably just kept going," said Cieslak.
      "What we had on paper we felt was not going to win."
      But this being the new GM where bean counters lost a fair amount of influence, the decision was made to go back to the drawing board. At the time, GM was scrambling to fix the Malibu as its redesign earned poor reviews and a drop in sales which likely played a part in this decision. They needed to get the Equinox redesign right as the model it would replace was very popular. There were concerns that this could cause the new Equinox to be delayed. But in the end, the team were able to design a new Equinox without falling off schedule.
      Source: Automotive News (Subscription Required)
    • By William Maley
      If it weren't for focus groups, the design of the 2018 Chevrolet Equinox could have looked so much different.
      Speaking to Automotive News, chief engineer of the 2018 Equinox Mark Cieslak revealed that focus groups weren't not impressed with the first designs of the redesigned model. They described the design as being bulky, 'not compelling', and looking a bit odd. If this was old GM, they would have gone forward with the design.
      "Back in the day, we would have probably just kept going," said Cieslak.
      "What we had on paper we felt was not going to win."
      But this being the new GM where bean counters lost a fair amount of influence, the decision was made to go back to the drawing board. At the time, GM was scrambling to fix the Malibu as its redesign earned poor reviews and a drop in sales which likely played a part in this decision. They needed to get the Equinox redesign right as the model it would replace was very popular. There were concerns that this could cause the new Equinox to be delayed. But in the end, the team were able to design a new Equinox without falling off schedule.
      Source: Automotive News (Subscription Required)

      View full article
    • By dfelt
      G. David Felt - Staff Writer Alternative Energy - www.cheersandgears.com
      Tesla Officially in Trouble, Business Insider Says!

      To quote Business Insider final comments on Tesla and the Chevy Bolt:
      "Clearly, Tesla would be in less trouble if the Chevy Bolt were a bad car. But it isn't. Teslas have always blown me away. The Bolt blew me away for different reasons. I just hope Tesla is prepared to take this into account." 
      Matthew is a Business Insider senior correspondent who covers transportation and as a fan of Tesla was excited to check out a Chevy BOLT as comparison to the Tesla. On a recent trip to california he took time to visit the closet Chevrolet Dealer to his hotel and this is what he found.
      He states that to borrow Barkley's line, "Tesla is in trouble." You have one of the world's biggest auto companies that is known for killing the electric auto stepping off the sidelines and actually committing considerable resources to building a long range EV where it can afford to lose money on it long term till the market changes. Tesla has 400,000 plus pre-orders, but is burning through cash by the billions and while the launch of the Tesla 3 is near and Tesla still has Sexy much like Apple to an iPhone. Tesla does not have the depth of customer auto experience to pull from and as the author points out, Tesla balance sheet is precarious as it is based on raising funds on a growth story. The author goes onto say that no one will cross shop a Tesla S or X with the Chevy BOLT. They will due to limited options cross shop the Tesla 3 to the Bolt.
      To pull some interesting statements from the story, the author had the following to say:
      "I found it more fun to drive than both the Tesla Model S and the Model X, but not the original Roadster, a much smaller vehicle."
      "The Bolt is plenty fast for most people."
      "GM isn't going to overwhelm Tesla with Bolt sales. I actually think the Model 3 will greatly outsell the Bolt once Tesla's car arrives. However, it's also possible that if the Model 3 is delayed or is slow to ramp up, Chevy will be preparing a mid-cycle refresh of the Bolt before Model 3 sales start to achieve some major momentum. In other words, GM will always be ahead, and the company — barring another massive financial meltdown — will never stop putting the Bolt up against the Model 3."
      BI covered the BOLT in follow stories with the next one being more of an official review that starts off with covering the auto with the following statement: "A platform, not business as usual!" 
      From ride-hailing to ride-sharing, self driving Chevy has delivered an auto for the future that gives GM options on how they build and expand their EV lineup. BI took delivery of their white Premier BOLT just before the blizzard that hit NY. Clearly a compact-crossover-hatchback look, design is what the magazine employees felt it was and is. Surprising the BI reviewers was the amount of cargo the auto can hold and how well it handled 4 people and grocery getting. BI states that GM has told them the next addition to the BOLT lineup will be a larger auto that can accommodate 5 or more people. An exceptionally well executed minimalist design that comes with an interior that feels more premium in comparison to auto's this size in the past from GM that felt clearly parts bin cheap. The review goes on to talk about how setting the front seat for a 6'4" tall driver and getting in the back with room ahead of the knees for the same size person is a nice welcome addition to such a compact auto. Heated steering wheel was welcomed by all. Apple CarPlay and Android Auto kept everyone happily connected to their phone while driving.
      The final statement to quote from the review is as follows:
      "We were impressed with the Bolt, as a car, as an electric car, and as a mobility concept. In many ways, it is GM's post-bankruptcy masterpiece, a real feather in the cap of CEO Mary Barra and her executive team, who took what the company had achieved with its ill-fated EV-1 back in the 1990s and turned it up to 11. 
      I also flat-out loved driving it. I blasted in and out of New York City twice, rocketed around the streets of Gotham, darting through traffic, and cruised along the highways of New Jersey. I also enjoyed just driving it around the quiet streets of the suburb where I live.
      The steering is quick and responsive, and the handling is sharp enough to provide the confidence you need when surfing that sweet EV torque.
      The single-pedal mode is also very cool — I dug not using the brakes at all for extended excursions in my town. After a bit of practice, you get into a kind of Zen state with it. 
      Not a single person asked me about the car, and that can be chalked up to the ho-hum design. But I didn't care. I was lovin' it. Plain and simple, the Bolt is fun."
      Here is where we have overlap between story #2 and Story #3 which covers the 7 Killer Features:
      Dual Screens- 10.2" touch screen infotainment center & an 8" drivers console display which are totally customizable. Auto's wireless charging console. BOLT App allowing you to be connected to your auto at all times. Five cameras: front, rear, side mirrors and their 360 camera. 9hr full charge time from a 240 volt charger. 25 miles per hour, faster with Level 3 DC charging. Lane Keep assist feature. Modern Seat design allowing for maximum space inside. Over all these writeups show that GM has delivered a superior auto to the Prius, Leaf, 500e, etc. The future will be bright for the BOLT as GM move the platform forward.

      BI Story #1
      BI Story #2
      BI Story #3
    • By William Maley
      Last week saw the PSA Group (parent company of Citroen and Peugeot) purchasing Opel and Vauxhall from General Motors for $2.3 billion. This move would make the PSA Group the second-largest automaker in Europe. We already know some of the plans that PSA Group has for their new brands such as setting operating profit targets of 2 percent in 2020 (jumps to 6 percent by 2026) and the next-generation Opel/Vauxhall Corsa being the first new product developed with PSA. But as we alluded to in the original news story, there are a lot of questions that remain unanswered such as possible job cuts or what happens to Buick and Holden as they share products with Opel. I have been doing a bit of thinking on these and some other questions. The end result is this piece.
      1: Will there be job cuts and plant closures?
      In 2016, PSA Group employed 172,000 people worldwide. With the acquisition of Opel and Vauxhall, they will be adding close to 42,000 workers (the majority of those from Opel). The number of plants will also increase to 28 due to this purchase. Sooner or later, PSA Group is going have to make cuts. During the press conference announcing the deal, PSA Group CEO Carlos Tavares said the company “would honor existing labor agreements and closing plants is a “simplistic” solution.” That may be true for now, but this might change within the coming years. Some analysts believe PSA Group will close two to three plants within five years.
      The most likely place where the closures and layoffs could take place is in Great Britain. The reason as we talked about in a story back in February deals with the decision made by British citizens last year with leaving the European Union.
      “By leaving, the country would lose access to the EU Single Market which guarantees unconstrained trade across the member states. It would mean various countries would be leveraging tariffs on British-made goods, making production in the country less competitive.”
      Former British member of parliament and business secretary Sir Vincent Cable outlined how bad this decision looks for Vauxhall in a recent interview on BBC Radio 4.
      There could be a way that the British Government could at least stall the possible closures. Back in October, the British Government worked out a secret deal with Nissan to keep them investing in British car production at their plant in Sunderland. This deal caused an uproar as the details were kept as many believed the British Government would be handing over money to keep Nissan happy. But sources told British newspaper The Independent back in January that the deal had no mention of money.
      It could be that the British Government could do something similar for PSA Group to keep jobs, but it is too early to say if this will happen or not.
      2: Will this affect PSA’s plans of entering the U.S.?
      Probably not. Let’s remember that PSA Group is working through a ten-year plan that may or may not see the return of the Citroen and Peugeot, along with the introduction of DS to the country. Already, the first part of this plan is gearing up for the launch of a car sharing service next month. There is also extensive research going on into the U.S. marketplace. 
      But could there be a possibility of Opel or Vauxhall vehicles being sold here? It would not be surprising if there isn’t talk about this at PSA Group’s HQ. But there is a slight complication to this idea. As part of the sale, PSA Group cannot sell any Opel vehicles developed by GM anywhere in various markets outside of Europe (China and U.S. for example) until they transition to PSA platforms. That means a number of models such as the Astra, Insignia, and Mokka are out of the question for the time being. If Opel was chosen to be one of the brands PSA would sell in the U.S., they might not have a full line of vehicles to sell due to this clause.
      3: What does the future hold for Buick and Holden?
      If there are some losers from the sale of Opel, it has to Buick and Holden. Buick has found some success with Opel products as the Encore (rebadged Mokka) has become one the best-selling models for the brand. Holden is getting a shot in the arm as the Astra will hopefully help their fortunes in the compact space, and the new Commodore (rebadged Insignia) has a tough task ahead of it with living up to an iconic name. For the time being, Opel will continue supplying models to both brands. It is what happens in the future that many are concerned about.
      During the Geneva Motor Show, GM President Dan Ammann said something very interest to Australian journalists about the future of Holden’s products.
      This makes sense as the Astra was only launched and the Commodore is getting ready to go on sale. But I wouldn’t be surprised if talks begin very soon about this very topic. The same talks are likely to begin at Buick soon where they face the same issue for the Regal and Encore. Our hunch is Buick might have the easier time of two. The Encore would continue on since it shares the same platform as the Chevrolet Trax. As for the Regal, it could leave Buick’s lineup once the next-generation model runs its course.
      4: Does GM lose anything with this deal?
      There has been a lot of talk about how much money will be freed up from the sale of Opel/Vauxhall for GM, along with making a bit more profit. But it comes at a cost that could hurt GM down the road. The recent crop of compact and midsize sedans from GM owe a lot to Opel’s engineering knowledge. Vehicles that excel in driving dynamics and fuel economy are worth their weight in gold when it comes to the European marketplace. As we know, one part of why GM went into bankruptcy was the lack of competitive small and midsize cars that got good fuel economy. Opel would prove to be GM’s savior with this key knowledge.
      Right now, compacts and midsize sedans aren’t selling as consumers are directing their attention to crossovers and SUVs. This is due in part to lower gas prices. But sooner or later, the price of gas will go back up and cause many to go back to smaller vehicles. With talk about GM scaling back on their small and midsize car lineup, this decision could have consequences down the road. Plus with Opel out of the picture, GM doesn’t have someone it can rely on to get these models back to the forefront. We can hope GM’s North American office has learned some stuff when working with their European counterparts.
  • Recent Status Updates

  • Who's Online (See full list)